Welcome - Please Read

Welcome. I wanted to provide stripboard layouts I've made to help people new to electronics and even the more experienced get into different aspects of electronics.

I verify the layouts before I post them.

My Facebook Group: www.facebook.com/StripboardLayouts - Please Add For Updates!
My Twitter Thing: @InSonicBloom

Wednesday, 2 October 2013

Logic Pulse Generator - Logic Pulser Stripboard Veroboard Layout


Often with projects that uses Logic devices such as previous projects like the devils drone sequencer or the Sound Activated Dancing LEDs you need to create a clock signal to make the logic transition from one state to the other. you don't want to have to deal with the clock (or oscillator) part of the circuit in the experimentation stage so you need something that is capable of creating a clock signal. This is just that piece of test gear.

it also uses the same power supply you're using to power the Logic ICs in question.

here is an example of a commercial version http://uk.rs-online.com/web/p/needle-point-probes/5375163/?origin=PSF_437277|alt

aswell as the layout and schematic - I have included some oscilloscope pictures of what it actually does.

Sorry if my explanation is a little off today in the making sense department - I am suffering from cluster migraines and one of the symptoms is Aphasia. the important thing is that the actual layout and circuit are correct - which as you can see - is the case!




As you can see I have soldered a nail to the pulse output - I've found this is the ideal probe



Thursday, 26 September 2013

Adjustable Pocket Power Supply Stripboard Veroboard Layout

This is something I've been meaning to make for quite a while.

Basically the idea was that should you go around charity shops, car boot sales, yard sales, thrift stores and other such places it would be nice to have a power supply capable of giving you various voltages to check if things you are potentially going to buy actually work. the resistors are selected for 3 volts, 5 volts, 9 volts and 12 volts and you may notice that the resistor values (R2, R3, R4 and R5) are very specific and in some cases not available - these values are due to not being able to alter R1 when you switch the voltage.  

there are 2 ways to get around this

1.add resistors in series or parallel eg. for R5 I put 2K and a 68r resistor in series and that was near enough to get me my 12 volt output

OR..

2. use 5K/4.7K trimpots and calibrate with your DMM - using that method you can of course easily set it for voltages you think you will need the most.


Saturday, 21 September 2013

Sound Activated Dancing LEDs Stripboard Veroboard Layout ( for the holiday seasons )


With all the various holidays coming up I thought I would do a nice decorative project. This makes LEDs light up with any kind of sound - it might make a cool halloween effect that makes LEDs flicker as people walk past your house or you could have it on your TV or something at christmas or of course anything else you could think of (if you have any ideas let me know)

as usual it is built and tested - it works beautifully and is quite sensitve however if you want to control the sensitivity change R4 to something like a 2K potentiometer or trim pot and adjust to suit.

for the microphone I used one I salvaged from and old phone similar to ( Mouser number 665-POM5238PR ) but I'm sure any kind of microphone will work.




Wednesday, 11 September 2013

S.A.L.O. (Smooth And Light Overdrive) Stripboard Veroboard Layout


This is just a little overdrive circuit I threw together the other day - I had an MXR octave fuzz that refused to work so I gutted it and made this thing to fill the box.

I didn't use a schematic or any pre-planning I just threw it together and hoped it did something and it did and it was quite a pleasing something. I will trace it so I've got a schematic to post at some point but until then here is the layout



The first 10 seconds is the guitar with no overdrive on

Devils Drone Sequencer Veroboard Stripboard Layout


This has taken some time to design and it's not perfect but it sounds pretty cool (As you can hear from the sample) it follows on from the devils triangle I did earlier this year ( Found HERE and no you don't have to build that to make this work!)
This is quite a big project and as you can hear I have built it using the stripboard layout provided (as I do with all my layouts) so take your time because I really can't spend lots of time answering why things don't work. The truth is that unless you have the board in front of you there is no possible way to troubleshoot things. But if you take it slowly it should be good.
also don't forget to check out the "tips and troubleshooting" page above

I would also recommend not to do this if you're in-experienced




Saturday, 24 August 2013

Marshall Bluesbreaker Stripboard Veroboard Layout


There is no schematic for this because I did this one years and years ago and I can't find the schematic that had the right component numbers to it and usually it causes confusion when components don't match their numbers on the schematics.
This particular layout was made from tracing an original unit and some of the component values differ from schematics that are on the net and I assume that they either cloned theirs without removing the components and measuring them and just went by what the component was marked as - this is where people go wrong because some manufacturers mark their components wrong to hinder cloners.

anyway here is the layout


Mini Push Pull Amplifier Stripboard Veroboard Layout


This is a bit of an experimentalist amplifier - the transistors on the BoM won't give you that much amplification however if you put some power transistors in there like BDT63/BDT62 you will get a lot more amplification.

I made this for my iPods headphones and essentially what I did is make one board for each channel so I can stack them on top of each other and it is quite a compact nice little amp.




Tuesday, 20 August 2013

Peizo Pickup Transducer Preamp Stripboard Veroboard Layout


this is actually from a request from a guy called Jim (sorry don't know your last name) who wanted a peizo preamp because they are so expensive. they are essentially just a high impedance preamp
and you could probably use this for other things like hiZ microphones and whatever.

there is a gain control on this and it uses an op-amp that is able to function as a single rail op-amp which cuts down the component count which is always useful when you need to hide this inside a guitar cavity or something.



Sunday, 28 July 2013

Poor Mans Audio Signal Generator Stripboard Veroboard Layout


this is something I made in school 15 odd years ago. you had to take a square wave, use a passive filter network to convert the signal to triangle and sine - this also has square and integrator waveforms. it's quite good up to 1 KHz but after that it starts to clip and go funny but it's more than adequate as an extremely cheap audio signal generator using 2 transistors and 1 LM555 timer IC - if you've gone through alot of my projects you'll notice how useful this IC is by now.

I have done another signal generator project that uses a proprietary ICL8038 IC Project can be found HERE which is more fully featured as far as project function generators go but the IC can be costly in certain places where as you can go on the grey market (IE eBay china sellers) and pick up hundreds of them for next to nothing.




Saturday, 20 July 2013

Adjustable Mains Hum Notch Filter Stripboard Veroboard Layout


I built this for those of you who have guitars with single coil pickups or indeed anything that picks up mains interference up (that annoying set of speakers in my bed room for example) anyway this little device reduces the mains hum by several orders of magnitude

it is adjustable between 45Hz and 90Hz so just put it before your amp or whatever and adjust the trim pot till the hum goes away.

it uses the same Texas Instruments TLC071 OP-AMP as I used in the last project for pretty much the same reason