tag:blogger.com,1999:blog-3033460626772757790.post2226236773927483786..comments2024-03-25T18:41:36.946+00:00Comments on Paul In The Lab: Boss OD1 14 Pin Version Stripboard VeroboardDrStevensonhttp://www.blogger.com/profile/13901235832359203061noreply@blogger.comBlogger7125tag:blogger.com,1999:blog-3033460626772757790.post-75127348508719394692015-01-15T19:02:52.157+00:002015-01-15T19:02:52.157+00:00there is a new version of this http://www.paulinth...there is a new version of this http://www.paulinthelab.com/2015/01/boss-od-1-original-rc3403-quad-op-amp.html<br />the 1M pot is gain and the 10K pot is volDrStevensonhttps://www.blogger.com/profile/13901235832359203061noreply@blogger.comtag:blogger.com,1999:blog-3033460626772757790.post-4696769823255855162015-01-08T03:39:30.042+00:002015-01-08T03:39:30.042+00:00which pot is volume and which is gain? Thanks agai...which pot is volume and which is gain? Thanks again!Will Traynorhttps://www.blogger.com/profile/17041905788584314710noreply@blogger.comtag:blogger.com,1999:blog-3033460626772757790.post-69191522592780072782014-12-30T23:15:53.696+00:002014-12-30T23:15:53.696+00:00I did this one so long a go (that's why the la...I did this one so long a go (that's why the layout is very spacious) I can't remember much but if my memory serves - if you increase R5 you should get more gainDrStevensonhttps://www.blogger.com/profile/13901235832359203061noreply@blogger.comtag:blogger.com,1999:blog-3033460626772757790.post-76110902895356779702014-12-30T21:55:55.615+00:002014-12-30T21:55:55.615+00:00Hi, I'm wanting to build this pedal but increa...Hi, I'm wanting to build this pedal but increase the amount of gain available. Which component is responsible for the max gain? Thanks so much for the layout by the way!Will Traynorhttps://www.blogger.com/profile/17041905788584314710noreply@blogger.comtag:blogger.com,1999:blog-3033460626772757790.post-60576943696510395702014-01-30T21:27:59.408+00:002014-01-30T21:27:59.408+00:00when I did this - I just found the schematic on go...when I did this - I just found the schematic on google - it was quite some time before I did this blog so I haven't got a clue where it is now. <br />I can't absolutely confirm that you can use the RC3403 because the only one I had was a pre-used and highly abused one and it didn't sound right but when I put the equivalents in it - it worked well so I imagine you can use the RC3403 but it won't sound any different it will just cost more. <br /><br />with the pots the 1M/10K refers to the pot value in ohms and the number after those are the lugs they are wired to - <br /><br />eg "1M 1-2" is a 1 megohm pot with the board wired to lugs 1 and 2 on the potDrStevensonhttps://www.blogger.com/profile/13901235832359203061noreply@blogger.comtag:blogger.com,1999:blog-3033460626772757790.post-45517305437104551722014-01-30T20:46:34.379+00:002014-01-30T20:46:34.379+00:00Maybe a dumb question but can you use the RC3403D ...Maybe a dumb question but can you use the RC3403D with this layout? Is there a schematic that you used for this layout available? Also, could you show the pot wiring?<br /><br /><br />CheersMark Vhttp://www.nashvillemusicphotos.comnoreply@blogger.comtag:blogger.com,1999:blog-3033460626772757790.post-19245841667825749012014-01-08T10:20:54.960+00:002014-01-08T10:20:54.960+00:00hi. thanks for this good job. Can you tell me what...hi. thanks for this good job. Can you tell me what are the ref. about the D2 & D3 ? Thank you. Regards. Bruno (from FRANCE). Mail to : incimis@hotmail.frAnonymousnoreply@blogger.com